- Manuals
- Brands
- U-Line Manuals
- Packaging equipment
- H-2079
- Operation instructions manual
Polypropylene
Hide thumbs Also See for H-2079:
- Troubleshooting manual (9 pages) ,
- Manual (10 pages)
-
- Contents
- Table of Contents
- Troubleshooting
- Bookmarks
Table of Contents
-
Maintenance
-
Troubleshooting
-
Instructions de Fonctionnement
-
Entretien
-
Dépannage
Advertisem*nt
Available languages
- EN
Available languages
- ENGLISH, page 1
Quick Links
- 1 Troubleshooting
- Download this manual
π
H-2079
POLYPROPYLENE
STRAPPING MACHINE
TECHNICAL DATA
CSA COMPLIANT
Strapping Speed: 2.5 Seconds/Strap
Dimensions: 35½" L x 23" W x 30½" H
Net Weight: 220 lbs.
Max. Tension: 100 lbs.
Strap Width: ¼" –
5
⁄
"
8
Core Capacity: Uses 8 x 8", 9 x 8" or 11 x 8"
(Core Dia. x Width)
Safety Switch: Stops machine when top is lifted.
Power: 110 VAC, 50/60 Hz, Single phase.
Open lid and remove contents from tray. Install package guide on lid.
L
O
A
D
R
E
L E
Right Side
1.
Remove plastic reel from machine. It comes preset
for 9" core. Remove outer ring adapter for 8" core. For
11" strapping core, the H-959-TC075 adapter can be
purchased.
2.
Load Strapping onto reel. DO NOT REMOVE BANDING UNTIL
LOADED. Make sure strap is going in correct direction
indicated by arrow.
PAGE 1 OF 8
1-800-295-5510
uline.ca
MACHINE SETUP
R
Remove adapter
before installing
reel.
POW ER
LEN GTH
RES ET
3
2
FEE D
ON
4
5
OFF
MAX
M
O
U
E T
S
R T
A
P P
N I
G
1.
Pull slide roller bar down and thread strapping over (1)
and under (2). Thread strap through guide (Ref 10) until it
reaches top of machine.
Pour le français, consulter les pages 5-8.
1
SLIDE ROLLER
2
BAND GUIDE
ROLLER
1212 IH-2079
Table ofContents
Advertisem*nt
Table of Contents
Related Manuals for U-Line H-2079
-
Packaging equipment U-Line H-2079 Manual
Polypropylene strapping machine (10 pages)
-
Packaging equipment U-Line H-2079 Troubleshooting Manual
Polypropylene strapping machine (9 pages)
-
Packaging equipment U-Line Green Machine H-3518 Instructions
Air pillow machine (3 pages)
-
Packaging equipment U-Line H-3518 Manual
Green machine air pillow machine (16 pages)
-
Packaging equipment U-Line H-7241 User Manual
Air cushion machine (28 pages)
-
Packaging equipment U-Line H-1459 Manual
Bag on a roll system (8 pages)
-
Packaging equipment U-Line H-959 Troubleshooting Manual
Polypropylene strapping machine (9 pages)
-
Packaging equipment U-Line H-951 Manual
Shrink tunnel (22 pages)
-
Packaging equipment U-Line H-140 Manual
Industrial shrink wrap system (5 pages)
-
Packaging equipment U-Line H-7242 Manual
Air cushion machine (27 pages)
-
Packaging equipment U-Line H-1482 Quick Start Manual
Steel tensioner (3 pages)
-
Packaging equipment U-Line H-7630 Manual
Packing station (28 pages)
-
Packaging equipment U-Line H-5334 Manual
Automatic tabletop paper crumpler (2 pages)
-
Packaging equipment U-Line H-5334 Quick Start Manual
Tabletop paper machine (10 pages)
-
Packaging equipment U-Line H-573 Operating Instructions
Deluxe strapping tensioner (3 pages)
-
Packaging equipment U-Line H-528 Quick Start Manual
High tensile steel tensioner (3 pages)
Summary of Contents for U-Line H-2079
- Page 1 Pour le français, consulter les pages 5-8. π H-2079 1-800-295-5510 uline.ca POLYPROPYLENE STRAPPING MACHINE POW ER LEN GTH RES ET FEE D TECHNICAL DATA CSA COMPLIANT Strapping Speed: 2.5 Seconds/Strap Dimensions: 35½" L x 23" W x 30½" H Net Weight: 220 lbs.
- Page 2 OPERATION INSTRUCTIONS Set strap feed length: Determine the length of strap needed. Set control for 0-6. Lengths listed in meters. 1 = 3 ft. of strap. Example: for 6 ft. of strapping, set the FEED RESET control at "2". (See Figure 1) Turn power ON.
-
Page 3: Maintenance
ADJUSTMENTS STRAP WIDTH Make adjustments at the strap outlet and the strap inlet. Machine comes preset for ⁄" strapping. Strap Inlet: Loosen two black screws with Allen wrench. Set Figure 5 Strap Inlet the strap inlet guide about ⁄" wider than the strapping you are using and align with the strap outlet. -
Page 4: Troubleshooting
TROUBLESHOOTING STRAPPING NOT SEALING Make sure machine is properly heated up (3-4 mins.). 2. Clean residue from top and bottom of heater blade with Scotch-Brite™ pad (S-11724). See "MAINTENANCE/ CLEANING" (page 3). STRAPPING JAMS IN INLET GROOVE Press RESET button on front panel. Figure 10 If jam remains, turn power switch OFF and pull strapping firmly until loose. - Page 5 π H-2079 1-800-295-5510 uline.ca CERCLEUSE POUR FEUILLARD DE POLYPROPYLÈNE POW ER LEN GTH RES ET FEE D DONNÉES TECHNIQUES CONFORME CSA Vitesse de cerclage : 2,5 secondes/feuillard Dimensions : L 90,2 cm, l 58,4 cm, H 77,5 cm (L 35,5 po, l 23 po, H 30,5 po) Poids net : 100 kg (220 lb) Tension max.
-
Page 6: Instructions De Fonctionnement
INSTRUCTIONS DE FONCTIONNEMENT Définir la longueur d’alimentation en feuillard : Déterminer la longueur de feuillard requise. Ajuster le contrôle de 0 à 6. Les longueurs sont indiquées en mètres. 1 = 91 cm ALIMENTER RÉINITIALISER de feuillard (3 pi) Exemple : pour 1,83 m de feuillard (6 pi), ajuster le contrôle à... -
Page 7: Entretien
AJUSTEMENTS LARGEUR DU FEUILLARD Faire les ajustements aux guides de sortie et d’insertion du feuillard. Guide La machine est préréglée pour un feuillard de 13 mm (½ po). d’insertion Figure 5 du feuillard 2. Guide d’insertion du feuillard : Desserrer les deux vis noires à... -
Page 8: Dépannage
DÉPANNAGE LE FEUILLARD NE COLLE PAS S’assurer que la machine est bien réchauffée (3 à 4 min.). Nettoyer les résidus sur les deux faces de la lame chauffante avec un tampon Scotch-Brite (S-11724). Voir « ENTRETIEN/NETTOYAGE » (page 3). LE FEUILLARD EST BLOQUÉ DANS LE SILLON D’INSERTION Figure 10 Appuyer sur le bouton RÉINITIALISER sur le panneau avant.